20Aug00

AT-11 Auto tuner

Considering the limitations of using the CAT feature and the FC-20 with the radio, some owners have opted to purchase the AT-11 auto tuner from LDG Electronics. This is available in either a kit or assembled format and does not suffer from the CAT/FC-20 limitations. You can see the review of the AT-11 by me in the reviews section of this main web page, if you want to learn more about it.

Update 08Jun00: The AT-11 tuner has undergone some major revisions and is now the AT-11MP model. It has some new features (e.g., meters, remote unit) that seem to be very nice.


[Return to Main Menu]



Modifications for the FT-847

Perhaps due to the relatively high cost of the radio, people do not appear to have delved too deeply into it and there are not many modifications available for it. There is the usual set of solder pads that are used to define the "country" for the radio. The company sets these depending on what country the radio will be sold in. Caution: modifying your radio in this manner may lead to the company not honoring the warranty. You can get some excellent information on the mods from Colin G1IVG's web page at http://personales.jet.es/colinlowe/index.htm. Also, see Opening up transmit range, below.

[Return to Main Menu]



Opening up transmit range

There is a set of six solder pads inside the radio that appear to give each radio it's "country identity" and to perhaps do other things. People have found that by changing the configuration of these solder pads, one can open up the transmit range of the radio. One caution: when the transmit range is opened to the full RX range of the radio, it is possible to transmit in the 36 MHz range which some say can destroy the RF power transistors. One good location showing how to make the mod is Colin Lowe's (G1IVG) web page, http://personales.jet.es/colinlowe/index.htm.

According to Colin, after doing his modification, the following transmit frequencies are available:

Band         Min TX freq.  Max TX freq.
H.F.                    1.8MHz             37MHz
VHF (A)              37MHz             76MHz
VHF (B)           137MHz           174MHz
UHF                 410MHz           470MHz 

DO NOT TRANSMIT OUT OF BAND, PLEASE!

Keep in mind that the FT-847 is not marketed as a "wide-band" receive (or TX!) radio, and it is not. Because of it's design, its performance is optimized for the transmit ranges that it comes with and it will not open up as widely as, say, the FT-50R or VX-1R and other HTs. One possibly undesirable feature of modifying the country designation is that the radio will no longer "know" what country it is set for, so the automatic repeater shift (ARS) feature will be lost on FM.

Also keep in mind that the transmit power will drop off quickly when transmitting outside the normal ham bands (which you should not be doing anyway unless you're driving a transverter). Also keep in mind that many of the antennas typically used on a radio of this type are not wide-band anyway.

Update 20Mar00: There is a wide variety of jumper settings that you can make that affect RX, TX, or both at once. Colin's page has a nice table that shows all the combinations of jumper settings and the RX and TX ranges for each setting of the blobs. Take a look. This information should be of interest to European hams, where the RX range is limited depending on the country in which the radio is marketed.

[Return to Main Menu]


Loss of ARS after TX Modification

If you do the modification to open up the transmit range, you will find that the Automatic Repeater Shift (ARS) feature no longer works. This is apparently due to the fact that the ARS is country-specific. You might ask why it wouldn't work on the new country's ARS pattern that you set the rig to. Don't know why. Perhaps the modifications that people have found change something besides just the country setting.

[Return to Main Menu]


Separate Receive and Transmit Lines on 2m & 70cm

Peter OZ1PIF has made a modification that will separate the RX and TX lines for 2m and 70cm. By adding two additional antenna jacks on the rear and by making a small mod inside, Peter has enabled a separate RX port for each of the two bands. This will facilitate adding pre-amps and interfacing amplifiers. You can see some detailed pictures of his modification by checking out his web site, http://hjem.get2net.dk/oz1pif/FT-847%20Mods.htm.

[Return to Main Menu]



Cat Control Operations

The FT-847 seems to have a set of unique op codes for CAT control. Yaesu in general, does not appear to have a consistent set of codes for any of their radios (unlike Kenwood for example).

Given that, you can't select another radio in a software offering that doesn't show the FT-847 specifically.

The original design for the FT-847 did not include two-way CAT control operations for frequency and mode. You could use your PC to give commands to the radio, but the radio could not report back any frequency or mode information to the PC. Many, including QST, complained about this shortfall, and the company modified the firmware in the radio to enable two-way CAT control operations for frequency and mode. Starting with serial number 8G05xxxx (see the explanation of serial numbers here), two-way CAT control is standard.

In a real credit to Yaesu, it offered to upgrade any earlier model radios to the two-way CAT control, so many of the earlier models have two-way CAT control. If you're buying a used FT-847, ask if it has been upgraded.

The CAT control for the FT-847 does not convey the final digit (i.e., the ones digit) under any circumstances, so no external software can ever resolve any frequency better than 10 Hz. The FT-847 itself resolves to 1 Hz.

[Return to Main Menu]



Polling Codes for Frequency & Mode

The FT-847, as originally delivered, could not poll the radio for frequency and mode information. This was added beginning with the 8G05 production runs. The Operating Manual does not show the codes for polling the radio. They are as follows.

To query the radio: Send a 5 byte sequence as follows: * * * * P1

Where *=Any value and P1=03 for Main VFO, 13 for RX Sat VFO, and 23 for TX Sat VFO.

Note that you cannot query the sub-VFO, nor can you swap VFOs via software.

The rig will return a 5 byte data sequence: D1 D2 D3 D4 D5

Where D1 contains the 100 MHz and 10MHz digits (in Hex format), D2 contains 1 MHz and 100 kHz digits, D3 contains 10 kHz and 1kHz digits, D4 contains 100 Hz and 10 Hz digits, and D5 contains mode data as follows: 00=LSB, 01=USB, 02=CW, 03=CW-R, 04=AM, 08=FM, 82=CW(N), 83=CW(N)-R, 84=AM(N), and 88=FM(N).

Example: 14 69 40 00 08 = 146.940.00, FM mode.

Note that you cannot poll or set the 1 Hz digit.

Page 91 in the manual describes sending frequency & mode to the radio; decoding it is similar.

[Return to Main Menu]



Raspy or FMing audio reports on SSB

There have been a number of postings like the following: "I have been getting signal reports that my FT-847 sounds very raspy and from what everyone is telling me it sounds like it is trying to FM on me when I am on USB. Seems to do it on all bands. Tried (3) different microphones including my Heil. Tried adjusting menus for treble and bass but nothing helps."

Replies have suggested that the problem was cured by moving the radio further away from the power supply. Apparently this is a problem with large linear supplies. My switching 30 amp supply is a foot away and I have no problems like this.

[Return to Main Menu]



Noise Blanker

In mid-June 1999, there were a number of postings regarding the noise blanker (NB) and its effectiveness. It was a mixed bag of experiences, however, where a couple could not find that it made any difference at all, and a few more said it was very effective. There was also some confusion as to what a noise blanker should cancel. The Operating Manual, on p. 21, says that it "may help reduce many different types of man-made impulse noise (but not atmospherics)." The DSP and Noise Reduction (NR), on the other hand, got high praise for effectiveness.

[Return to Main Menu]



Special & Hidden Menus

There are two special menus (at least), on the FT-847. One, documented in the Operating Manual, is accessed by changing Menu #42 EXTEND to ON. This activates menu choices 90 through 96. Since the features are discussed in the manual, I won't say any more here.

The other hidden menu is the Alignment Menu. The Operating Manual does not discuss this menu, but the Technical Supplement (the "service manual") does. To access this menu, you need the standard mike with the UP, DOWN, and FAST buttons. Hold down these three buttons simultaneously and turn on the radio using the power switch. This will place you into the alignment menu. Doing this does not cause a reset of your radio.

The FIRST thing to do after accessing the menu is to use the Sub-Tune knob to step through each setting and write down the values shown. There are 25 different variables that are identified by a mnemonic. The values are shown where the channel number normally displays on the display, and they are in hexadecimal format. The RX-GAIN and TX-GAIN parameters are band-specific, so you should write down the values for each band (each HF band, 6m, VHF, UHF).

On TX-GAIN the Technical Supplement has you do separate adjustments for 160m, 20m, 10m, 6m, 2m, and 70 cm. On RX-GAIN, it has you adjust 80m, 20m, 10m, 6m, 2m, and 70 cm.

There are two ways you can use the alignment menu. The first is to use the proper methods to establish the correct values. The second is to manually change the values for one or more parameters. Both are discussed below. By the way, not all the alignment steps for the radio can be done from the menu.

Thanks to David G7LMT for providing the correct information for the discussion below.

Also, Scott VE3SCP has done a full alignment of the rig and has some insights into the process and the Technical Supplement. He has offered to elmer people with questions. You can email Scott by clicking here.

Using test gear to establish and set the proper values (as described in the Technical Supplement)

1. Set up the machine as instructed in the Technical Supplement.

2. Go into alignment menu by pressing the UP, DOWN, and FAST keys on the stock microphone while turning the rig on with the power switch.

3. Use the SUB-TUNE knob to select the appropriate parameter.

4. Inject the appropriate signal into the appropriate port as instructed in the Technical Supplement. Press MCK/W to allow the resulting value to be logged onto the display. By pressing MCK/W, you are "taking the measurement." The numeric value, in hex format, is shown where the channel number usually shows on the display.

5. To set another parameter, Return to Step 3, or go to step 6 if you're finished.

6. To retain ("save") the resulting values for all the changes you have made to the system's memory, you then press the MENU button. This returns you to normal operation. NOTE: If you do NOT want to save the changes you've made, press POWER off without pressing the MENU button; this abandons the changes.

Manually setting the value for one or more parameters

If you want to manually set the value for a parameter, as opposed to using the test equipment as described above, you can do this as follows:

1. Hold down UP, FAST, and DOWN buttons while turning the rig on.

2. Use the SUB-TUNE knob to select the parameter you want to adjust.

3. Turn the MEM/VFO CH knob to manually change the value that is shown. This knob will increase or decrease the value depending on which way you turn it.

4. To set another parameter, return to Step 2, or go to Step 5 if finished.

5. To memorize ("store") the new value you just set manually, press the MENU key to memorize it. NOTE: If you want to abandon the changes you have made, press the POWER switch instead of the MENU key.

At least one of the menu parameters has two parameters; you get to the second one by pressing the A-B VFO swap button.

Now, I don't know what all of these settings do. The names are cryptic, to say the least, and the Technical Supplement doesn't help too much. What I do know is that a couple of hams have adjusted the DISC-L and DISC-H settings to bring their discriminator to the center setting. The other settings do not seem to do anything magic (like more power!); rather they set meters, RX gain, TX gain, carrier point adjustment, SWR "meter," etc. It looks like you can "undo" changes you have made if you want to return to the factory settings, but only if you've written them down! You're on your own, though! I reiterate my recommendation to get the Technical Supplement if you want to experiment with these settings.

Everyone who plays around with these settings is encouraged to submit posts explaining what he or she did and the results so the rest of us can learn from the experiments.

[Return to Main Menu]



Reports on the Alignment Menu

NOTE: Please read the discussion on Hidden Menus before reading the following reports from others! Read especially the section titled "Manually Setting the Value for One or More Parameters." These reports may not have been confirmed by others or me.

Adjusting the discriminator setting

Jim W4LC reported that he manually adjusted the DISC-L alignment setting slightly (one digit) and this caused his discriminator setting to show correctly on his "meter."

David G7LMT reported that he adjusted his DISC-H alignment setting by five digits to bring the discriminator to the correct setting.

Update 11/26/99: Chuck AA6G reported his results on adjusting the FM discriminator reading. This report is interesting because he used the menu to customize the discriminator to show deviation over the greater range than the stock settings. I'll reproduce his results verbatim.

"I was reading the FAQ and decided to adjust my discrinator setting since it was a little off too. I used an HP-8640B as the signal generator. It seemed as though the DISC-L and DISC-H menu items should be the low and high adjustments and indeed they appear to work that way. I found the total range of my meter to be less than 2KHz and I wanted a little more range.
I was able to get +/-5KHz by setting DISC-L to 21 and DISC-H to 38. My meter now moves off center one segment at about +/-500Hz. The tradeoff is less sensitivity to a small frequency change but a greater range. I suspect you [could] get +/-10KHz if you wanted it.

"You can perform this adjustment with an on-the-air signal if you have one you trust to be accurate.
Simply tune above and below the signal the amount you want and adjust the menu item so the meter just
reaches the limits."


Adjusting the Transmit Gain - PLEASE READ ENTIRE DISCUSSION BEFORE CHANGING ANYTHING!

I recently used the alignment menu to adjust my TX-GAIN to see what would happen. First, though, I wrote down what the setting was before doing anything. There are actually six different TX-GAIN settings: 70cm, 2m, 6m, 10m, 20m, and 160m. You will need to tune your rig to the band you want to adjust, then go into the alignment menu by holding down the three buttons on your stock mike while turning the rig on. Use the Sub-Tune knob to turn to TX-GAIN. Write down the setting, and remember that it's only for the band you're on. Now, you can use the MEM/VFO CH knob to change the TX-GAIN value. Mine was at 8F to begin with, and I was working on the 2m band.

As I reduced the values, nothing happened until I got down to about 48. Between 48 and about 41, the output power began to drop off quite a bit. By 40, I could not measure any output on my watt meter. I then returned the setting to 8F and things were back to normal. I did not try increasing the value beyond 8F. Even after changing this value, you can use the RF PWR knob to reduce the power below the maximum value.

You can actually check things as you go. After turning the MEM/VFO CH knob, you can still change modes and key the rig with a CW carrier. This way, you can check the resulting output instantly without having to return to normal operations. Once you have a setting you want, press the MENU button to return to normal operations. You can return to the alignment menu as often as you want to change things some more.

This ability would seem to be particularly helpful for hams running amps that have, say, a 10 watt input. If you're always using the amp, you could adjust the TX-GAIN to limit output and protect your amplifier. There are some tradeoffs on doing these adjustments. Please see the discussion on Limiting Maximum Output Power for an explanation from Yaesu.

Note: Two of us have stumbled onto something you should know about. We think that, if you are fooling around with TX-GAIN and you change bands with the band switches while you are in the alignment menu, it may transfer the TX-GAIN setting to the register for the band you just switched to. All the more reason to write down all the values before you begin fooling around with the Alignment Menu.

Update 20Aug00: Another way to control power output of your FT-847 is by using the ALC control circuit. Click here to read about how to use ALC to control power output.


[Return to Main Menu]


Typical Alignment Menu Settings

I include here my alignment menu settings in case it might help someone with a problem. I don't think I've changed any of these from what the rig came with (but I might have!). I'm sure your settings will be somewhat different from these, so this information should be used for comparisons only. There are 25 different settings and some of those have multiple values, depending on what band you're on. I know that at least one has two values that are accessed by using the A-B swap button. Also, I don't know what many of these do!


FM-S1 58
FM-FULL 89
RX-GAIN 75(160-30), 93(20-15), A2(12-10), 6B(6m), 43(2m), 47(.7m)
SQL-TH-L 5A
SQL-TI-L 00
DISC-L 24
DISC-H 30
SSB-S1 DD
SSB-S9 5E
SSB-FULL 26
SFT-CTR 7F
RXC-PNT 00
TXC-USB FE
TXC-LSB FA
PWR-100W 91
PWR-50W 62
PWR-20W 3E
PWR-10W 2B
ALC-1 06
ALC-9 2F
TX-GAIN AF(160-30), A8(20-10), 8F(6-2), 64(.7m)
SWR 1.5 12
SWR 3.0 3E
ALL-CLR 00
DSP-PASS 00

[Return to Main Menu]